series am1/4l-nz 1/4 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8.j 1 of 4 north america only features: models single output model input voltage (v) output voltage (v) output current max (ma) isolation (vdc) efficiency (%) am1/4l-0505s-nz 4.5-5.5 5 50 1000 64 am1/4l-1205s-nz 10.8-13.2 5 50 1000 65 am1/4l-0505sh30-nz 4.5-5.5 5 50 3000 64 am1/4l-1205sh30-nz 10.8-13.2 5 50 3000 66 am1/4l-1212sh30-nz 10.8-13.2 12 20 3000 67 models dual output model input voltage (v) output voltage (v) output current max (ma) isolation (vdc) efficiency (%) * am1/4l-2405d-nz 21.6-26.4 5 25 1000 62 am1/4l-0505dh30-nz 4.5-5.5 5 25 3000 64 * not recommended for new design note: add suffix ?tr? to a part number when ordering in tape and reel package input specifications parameters nominal typical maximum units parameters voltage range 5 4.5-5.5 vdc 12 10.8-13.2 24 21.6-26.4 filter capacitor isolation specifications parameters conditions typical rated units tested i/o voltage 60 sec 1000 & 3000 vdc resistance > 1000 mohm capacitance 60 pf output specifications parameters conditions typical maximum units voltage accuracy see the tolerance graph 5 % voltage balance dual output 2 % line voltage regulation (single) for 1% change of vin 1.2 % line voltage regulation (dual) for 1% change of vin 1.2 % load voltage regulation (single) load 10 ? 100% 10 % load voltage regulation (dual) load 10 ? 100% 10 % temperature coefficient 0.03 %/ o c ripple & noise at 20mhz bandwidth 75 mv p-p ? rohs compliant ? ? smd package ? ? low ripple and noise ? ? high efficiency up to 68% ?
series am1/4l-nz 1/4 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8.j 2 of 4 north america only general specifications parameters conditions typical maximum units switching frequency 100% load single 100 khz 100% load dual 150 khz short circuit protection momentary (1sec) operating temperature without derating -40 to +85 o c storage temperature -55 to +125 o c cooling free air convection humidity 95 % case material plastic ul94-vo weight 1.5 g dimensions (l x w x h) single 1000vdc 0.50 x 0.44 x 0.26 inch 12.70 x 11.20 x 6.70 mm dual 1000vdc 0.60 x 0.44 x 0.26 inch 15.24 x 11.20 x 6.70 mm single and dual 3000 vdc 0.60 x 0.44 x 0.26 inch 15.24 x 11.20 x 6.70 mm mtbf >3 500 000hrs (mil-hdbk -217f, ground benign, t=+25 o c) max case temperature 95 o c note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidit y<75%, nominal input voltage and at rated output load unless otherwise specified pin out specifications pin out specifications single and dual 1000vdc single and dual 3000vdc typical characteristics pin single dual 1 - v input - v input 2 + v input + v input 3 n.c. n.c. 5 -v output common 6 n.c. -v output 7 n.c. n.c. 8 +v output +v output 10 n.c. n.c. 11 n.c. n.c. 12 n.c. n.c. pin single 1 - v input 2 + v input 3 n.c. 4 - v output 5 + v output 6 n.c. 7 n.c. 8 n.c. pin dual 1 - v input 2 + v input 3 n.c. 4 common 5 - v output 6 n.c. 7 + v output 8 n.c. 9 n.c. 10 n.c. typical load line tolerance envelope graph output current (%) output voltage +2.5% -2.5% -7.5% + +5% 10% 50% 100% nominal voltage 10 %
series am1/4l-nz 1/4 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8.j 3 of 4 north america only dimensions single 1000vdc dimensions dual 1000vdc a 0.30 (0.01) 1.50 (0.06) 0.50 (0.02) 5.00o angle a 7.50 (0.30) 7.00 (0.28) 6.70 (0.26) top view front view side view 6.25 (0.25) 1.85 (0.07) 12.70 (0.50) 0.50 (0.02) 2.54 (0.10) 1 7.62 (0.30) 11.20 (0.44) 6.00 (0.24) 4.13 (0.16) 0.25 (0.01) all dimensions are in mm (inch) all pins are on a 2.54mm (0.10inch) pitch with tolerance of 0.25mm (0.01inch) a 0.30 (0.01) 1.50 (0.06) 0.50 (0.02) 5.00o angle a 7.50 (0.30) 7.00 (0.28) 6.70 (0.26) top view front view side view 6.25 (0.25) 1.85 (0.07) 15.24 (0.60) 0.50 (0.02) 2.54 (0.10) 1 7.62 (0.30) 11.20 (0.44) 6.00 (0.24) 4.13 (0.16) 0.25 (0.01) all dimensions are in mm (inch) all pins are on a 2.54mm (0.10inch) pitch with tolerance of 0.25mm (0.01inch)
series am1/4l-nz 1/4 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8.j 4 of 4 north america only dimensions single and dual 3000vdc note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without not ice. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency ce rtifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive test ing or chemical analysis on all internal components and chemicals at the time of publishing th is document. cas numbers and other limited information are considered proprietary an d may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in haz ardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. warranty is in accordance with aimtec?s standard terms of sale available at www.aimtec.com. a 0.30 (0.01) 1.50 (0.06) 0.50 (0.02) 5.00o angle a 7.50 (0.30) 7.00 (0.28) 6.70 (0.26) top view front view side view 6.25 (0.25) 1.85 (0.07) 15.24 (0.60) 0.50 (0.02) 2.54 (0.10) 1 11.20 (0.44) 6.00 (0.24) 4.13 (0.16) 0.25 (0.01) all dimensions are in mm (inch) all pins are on a 2.54mm (0.10inch) pitch with tolerance of 0.25mm (0.01inch)
|
